Home
Select the PoE standard and class per device.
How many PoE devices on this switch.
Recommended: 20–30% for cable loss & expansion.
Devices:
Overhead:

IEEE PoE Standards & Power Classes

Power available at the switch port (PSE) vs. power guaranteed at the device (PD) after worst-case cable loss. Class 0 is treated as Class 3. Classes 5–8 use all four pairs, halving cable loss compared to two-pair delivery.

Class PoE Type PSE Output (W) PD Input (W) Pairs Typical Devices
0 (default)802.3af Type 115.413.02IP phones, basic cameras
1802.3af Type 14.03.842Simple sensors, VoIP
2802.3af Type 17.06.492Wireless APs (legacy)
3802.3af Type 115.413.02IP phones, cameras
4802.3at Type 230.025.52HD cameras, dual-band APs
5802.3bt Type 345.040.04PTZ cameras, video phones
6802.3bt Type 360.051.04Multi-radio APs, sensors
7802.3bt Type 475.062.04High-power APs, LED panels
8802.3bt Type 490.071.34Wi-Fi 7 APs, large displays
Cisco UPOEProprietary60.0~514Cisco high-power devices
Cisco UPOE+Proprietary90.0~714Cisco high-power devices

What Is Cisco PoE?

Power over Ethernet (PoE) is a technology that allows a single Ethernet cable to carry both data and electrical power to devices such as IP phones, wireless access points, and surveillance cameras. Cisco has been a major driver of PoE adoption and offers switches supporting the full range of IEEE standards plus its own proprietary extensions.

Cisco PoE-capable switches act as Power Sourcing Equipment (PSE), providing power over the copper pairs of the Ethernet cable. The connected device is the Powered Device (PD).

IEEE PoE Standards Supported by Cisco

  • IEEE 802.3af (PoE, Type 1) — up to 15.4 W at the PSE, delivering ~13 W to the PD. Uses two pairs. Classes 0–3.
  • IEEE 802.3at (PoE+, Type 2) — up to 30 W at the PSE, ~25.5 W at the PD. Uses two pairs. Class 4.
  • IEEE 802.3bt (PoE++, 4PPoE, Types 3 & 4) — up to 60 W (Type 3) or 90 W (Type 4) at the PSE. Uses all four pairs. Classes 5–8.
  • Cisco UPOE (Universal Power Over Ethernet) — Cisco-proprietary, delivers up to 60 W over four pairs using CDP/LLDP negotiation.
  • Cisco UPOE+ — Enhanced version delivering up to 90 W for high-power devices.

PSE vs. PD Power: Why the Difference?

The power available at the switch port (PSE output) is always higher than the power guaranteed at the device (PD input). The difference is cable loss — energy dissipated as heat in the copper wires. The IEEE standards reserve a worst-case loss budget:

PPD = PPSE − I²Rcable

For 802.3af/at (two-pair delivery), the standard reserves enough loss budget for a 100 m cable. For 802.3bt (four-pair delivery), the current is split across more conductors, halving the I²R loss and allowing more power to reach the device.

Power Budgeting: The Golden Rule

A switch's PoE budget is the total power its power supply can deliver to PoE ports. The golden rule is:

Required Budget = Σ (Class Reservation per Device) × (1 + Overhead %)

The class reservation is the PSE output power (e.g., 30 W for Class 4), not the device's actual draw. Always add 20–30% overhead for cable loss, peak startup currents, and future expansion. Never plan to run a switch at 100% of its PoE budget.

Example: 10 × 802.3at devices (Class 4) require 10 × 30 W = 300 W. With 25% overhead, you need a switch with at least 375 W of PoE budget.

Cable Matters

Cable gauge and length affect voltage drop and power loss. Thicker wire (lower AWG number) has lower resistance. For high-power PoE (802.3bt, UPOE+), Cisco recommends Cat6A or better to minimize loss and heat. The Cable Power Loss mode estimates the I²R loss for a given cable run and PoE class.

Why Use This Cisco PoE Calculator?

  • Three modes: Budget sizing, maximum device count, and cable loss estimation.
  • Full standard coverage: 802.3af, 802.3at, 802.3bt Types 3 & 4, Cisco UPOE, and UPOE+.
  • PSE-accurate: Uses the power reserved at the switch port, not optimistic datasheet values.
  • Cable loss model: Estimates real I²R loss based on length and gauge.
  • Reference table: All classes and power levels in one place.
  • Free & private: Runs entirely in your browser — no data is sent to a server.

❓ Cisco PoE Calculator FAQ

What is the difference between PSE power and PD power?

PSE (Power Sourcing Equipment) power is what the switch must supply at its port. PD (Powered Device) power is what the device actually receives after cable loss. The PSE rating is always higher. For example, 802.3at provides 30 W at the PSE but only 25.5 W at the PD.

Why add 20–30% overhead to the PoE budget?

Cable loss, peak inrush currents at device startup, and future expansion all consume budget. Running a switch near 100% of its PoE capacity risks random device reboots and instability. A 20–30% margin is standard practice.

What is Cisco UPOE?

Cisco Universal Power Over Ethernet (UPOE) is a proprietary extension that delivers up to 60 W over four pairs using CDP or LLDP for power negotiation. UPOE+ extends this to 90 W. Both are available on many Catalyst switches.

Can I mix PoE classes on the same switch?

Yes. A PoE switch can power devices of different classes simultaneously, provided the total reserved power does not exceed the switch's PoE budget. The switch allocates power per port based on the detected class.

What cable should I use for high-power PoE?

For 802.3bt (60–90 W) and Cisco UPOE+, use Cat6A or better. Higher categories have thicker conductors (lower AWG) and better heat dissipation. Always check the cable's temperature rating when bundling many high-power PoE runs.

Does this calculator model voltage drop?

The Cable Power Loss mode estimates I²R power loss in watts. It does not display voltage at the PD, but the power loss figure gives you a direct indication of how much power is dissipated in the cable. For precise voltage drop, use a dedicated voltage drop calculator.

Is this calculator affiliated with Cisco?

No. This is an independent educational tool. Cisco, Catalyst, UPOE, and UPOE+ are trademarks of Cisco Systems, Inc. Always consult official Cisco documentation for critical deployments.

Is this calculator free?

Yes. This tool is completely free, requires no registration, and runs entirely in your browser. Your inputs are never sent to a server.